Timeshell

Featured

Genuine E3D V6 Gold HotEnd (24V)

E3D-Online

To celebrate the E3D V6’s third anniversary we wanted to do something special to show off the HotEnd..

$139.99 CAD

Genuine BLTouch : Auto Bed Leveling Sensor Probe Smart Edition V2

ANTCLABS

This is the newest version of BLTouch. Smart Edition V2 uses a plastic pin.BLTouch is an..

$45.99 CAD

E3D v6 HotEnd Full Kit - 1.75mm Universal (Direct) (12v)

E3D-Online

The E3D V6 Hot End: Smaller, Easier, High PerformanceThe E3D V6 is our market-leading signature Hot ..

$89.99 CAD

EcoTough™ PLA Filament - Blue - 1.75mm

Filaments.ca

Free local pickup or delivery may be available in Port Hope and Cobourg. Please inquire at tim..

$32.99 CAD

EcoTough™ PLA Filament - Red - 1.75mm

Filaments.ca

Free local pickup or delivery may be available in Port Hope and Cobourg. Please inquire at tim..

$32.99 CAD

EcoTough™ PLA Filament - WHITE - 1.75mm

Filaments.ca

Free local pickup or delivery may be available in Port Hope and Cobourg. Please inquire at tim..

$32.99 CAD

Bestsellers

Capricorn Bowden Tubing (100mm)

Capricorn

Your extruder system has a finite amount of pushing force. You want as much as possible of that push..

$1.99 CAD

LM2596 Adjustable DC-DC Buck Converter Step Down Voltage Regulator

Miscellaneous

DescriptionChip: LM2596SInput Voltage: 3V - 35V (must be at least 1.5V higher then output)Output Vol..

$2.99 CAD

625-2RS Rubber Sealed Ball Bearing Bearings 5mm x 16mm x 5mm

CMB

Deep Groove Ball Bearing 625-2RSISO CertificateISO 9001:2008DimensionID (Inner D..

$1.25 CAD

Genuine E3D Collet Clips (Pack of 2)

E3D-Online

These collet clips are designed to eliminate the backlash created by the collet in our embedded bowd..

$0.25 CAD

Latest

New

Trinamic TMC2130 Stepper Driver Board SilentStepStick

Trinamic Motion Control GmbH

DESCRIPTION The TMC2130 is a high performance driver IC for two phase stepper motors. Standard SP..

$21.99 CAD

New

Trinamic 2130 Stepper Driver Board SilentStepStick

DESCRIPTION The TMC2130 is a high performance driver IC for two phase stepper motors. Standard SP..

$19.99 CAD

New

Trinamic 2130 Stepper Driver Board SilentStepStick

Trinamic Motion Control GmbH

DESCRIPTION The TMC2130 is a high performance driver IC for two phase stepper motors. Standard SP..

$19.99 CAD

2-3 Days

EcoTough™ PLA Filament - Pearl Gold - 1.75mm

Filaments.ca

Free local pickup or delivery may be available in Port Hope and Cobourg. Please inquire at tim..

$32.99 CAD

Latest Articles - All Articles

How to Connect MKS TFT to Smoothieboard

Posted by Greg Nutt | On 19.06.2018 | Added in Wiki Links |

The MKS TFT32 is a fantastic self-contained controller which, among others, can control the Smoothieboard via the serial interface. The connection method is fairly easy but will require a couple manual hardware and setting configurations. 1. The cable that comes with the MKS TFT32 will need to have the 8 pin connector removed on one end and replaced with a 6 pin straight connector matched pin for pin with the 6 pin serial pins on the Smoothieboard. Make sure that the TX on the MKS TFT32 goes to the RX on the Smoothieboard and v..

Wiki Links

Posted by Greg Nutt | On 08.02.2018 | Updated on 19.06.2018 |

Your guide to installing Smoothieboard in a 3D printerBLTouch ManualE3D Online DocumentationHow to Connect MKS TFT to Smoothieboard..

What Kind of Nozzle Should I Use?

Posted by Greg Nutt | On 17.01.2018 | Updated on 17.01.2018 |

The most common nozzle used in 3D printers today is no doubt the 0.4mm brass nozzle. This works fine for the basic filaments like ABS, PLA, ASA, and PETG and many others. But, there are more exotic filaments out there that are much more abrasive than these filaments and will very quickly wear down the tiny hole in your brass nozzle, causing it to become enlarged and misshapen which will progressively degrade the quality of your 3D prints. These other filaments include filaments such as carbon fiber, wood fiber, filament containing metallic particles and so on. So, if yo..

Does Wire Size Matter in My 3D Printer?

Posted by Greg Nutt | On 15.11.2016 | Updated on 15.11.2016 |

Many 3D printer enthusiasts may be for the first time diving into electronics tinkering. The electronics landscape is very different today than it was 30 years ago. Today we have micro-controllers and breakout boards and a lot of the harder design work is already done for you. But the fundamentals themselves have not changed.Choosing the correct wire size for your 3D printer's motors, hotend, heat bed and sensors is very important. It is not always one size fits all.Let's compare a wire to a water pipe for a moment. A water pipe carries a certain volume of ..

0 comments on this article - view comments